(Click Image to Enlarge)

Side Post Battery Cables

I make these cables to replace the old and undersize cables that come on these cars. These cables will help with the starting and charging system, you will also notice brighter lights.

I make these cables using 1/0 gauge copper cable for the starter (46") long, and 2 gauge copper cable for the alternator (20") long and junction box (18") long, 1/0 gauge copper cable engine ground (36") long and 2 gauge copper cable body ground (12") long. Solid copper ends are soldered and crimped on for the best connection, then adhesive lined shrink is installed for protection. I then install flame retardant loom and battery and alternator boots. I supply new clamps for the starter cable to frame and new battery hardware.

Available for: Firebird Formula, Trans AM LT1

(Click Image to Enlarge)

Top Post Battery Cables LT1

Top post battery cables with loom and boots LT1: $90.00

(Click Image to Enlarge)

LS1 Battery Cables

I make these cables using 2 gauge copper cable for the starter, alternator, fuse box and ground. Solid copper ends are soldered and crimped on for the best connection, then adhesive lined shrink is installed for protection. I then install flame retardant loom and battery and alternator boots. I supply new clamps for the cables to chassis and new battery hardware.

Available for: Firebird Formula, Trans AM

LS1 Sidepost battery cables with loom and boots: $90.00

(Click Image to Enlarge)

LS1 Upgraded Battery Cables for High Output Alternators

I am now making the following upgraded cables for use with high output alternators: Power cables are 1/0 gauge alternator cable, 1/0 gauge starter cable, and 2 gauge fuse box cable. Ground cables are 1/0 gauge engine ground, 1/0 gauge body ground. Cable sets are complete with loom and hardware. This is a must if you are using a 200Amp or higher alternator.

LS1 Sidepost H/O Battery Cables: $95.00

(Click Image to Enlarge)

88-89 Trans Am Battery Cables

I make these cables to replace the old and undersize cables that come on these cars. These cables will help with the starting and charging system, you will also notice brighter lights. I make these cables using 1/0 gauge copper cable for the starter cable( 75"), and 2 gauge copper cable for the alternator (30") and 10 gauge wire (12") for pigtail with female weatherpak connector and 10 gauge (12") for pigtail with male weatherpak connector. 1/0 gauge copper cable for the engine ground (32") and 2 gauge for the body ground (12"). Solid copper ends are soldered and crimped on for the best connection, then adhesive lined shrink is installed for protection. I then install flame retardant loom and battery and alternator boots. I supply a new clamp for the starter cable to frame and new stainless steel battery hardware.

88-89 Trans Am Sidepost Battery Cables: $80.00

88-89 Trans Am H/O Battery Cables

I make these cables to replace the old and undersize cables that come on these cars. These cables will help with the starting and charging system, you will also notice brighter lights. I make these cables using 1/0 gauge copper cable for the starter cable (75"), and 1/0 gauge copper cable for the alternator (30") and 10 gauge (12")wire for pigtail with female weatherpak connectors and 10 gauge (12") wire for pigtail with male weatherpak connector. 1/0 gauge copper cable for the engine ground (32") and 1/0 gauge for the body ground (12"). Solid copper ends are soldered and crimped on for the best connection, then adhesive lined shrink is installed for protection. I then install flame retardant loom and battery and alternator boots. I supply a new clamp for the starter cable to frame and new stainless steel battery hardware.

88-89 Trans Am Sidepost Battery Cables: $90.00

(Click Image to Enlarge)

1990-92 Trans-Am Battery Cables

I make these cables to replace the old and undersize cables that come on these cars. These cables will help with the starting and charging system, you will also notice brighter lights. I make these cables using 1/0 gauge copper cable for the starter cable,(75") and 2 gauge copper cable for the alternator (36") and 10 gauge wire for both pigtail with connector (12"), 1/0 gauge copper cable for the engine ground (32") and 2 gauge for the body ground (12"). Solid copper ends are soldered and crimped on for the best connection, then adhesive lined shrink is installed for protection. I then install flame retardant loom and battery and alternator boots. I supply a new clamp for the starter cable to frame and new stainless steel battery hardware.

Please make sure your cables have the same connector as shown in the picture.

1990-92 Trans-Am Sidepost Battery Cables: $80.00

(Click Image to Enlarge)

1990-92 Trans-Am H/O Battery Cables

I make these cables to replace the old and undersize cables that come on these cars. These cables will help with the starting and charging system, you will also notice brighter lights. I make these cables using 1/0 gauge copper cable for the starter cable (75"), and 1/0 gauge copper cable for the alternator (36") and 10 gauge wire for both pigtails with connector (12"), 1/0 gauge copper cable for the engine ground (32") and 1/0 gauge for the body ground (12"). Solid copper ends are soldered and crimped on for the best connection, then adhesive lined shrink is installed for protection. I then install flame retardant loom and battery and alternator boots. I supply a new clamp for the starter cable to frame and new stainless steel battery hardware.

Please make sure your connector looks like one in the picture.

1990-92 Trans-Am H/O Sidepost Battery Cables: $90.00

(Click Image to Enlarge)

MAF Extention Cable

I am making MAF extension cable to work on LT1 cars.

So now you can more your MAF to wherever you wish.

I will make the cable in any length you may need.

MAF Cable:$20.00

(Click Image to Enlarge)

OPTISPARK Harness 95-96

This is a direct replacement harness with all terminals crimped, solderd, and loom is installed to protect the wires.

Optispark Harness 95-96: $45.00

(rollover image for connector view)	O2 Extension Harness (black flat 4-pin) These O2 extension harness are for the cars that need to move their O2 sensors back when running long tube headers. The terminals are factory style crimped and soldered and loom installed to help protect the wires. This harness uses the black flat 4-pin style connectors. Available in different lengths. O2 Extension Harness: $15.00ea Select length: 6" O2 Harness 12" O2 Harness 18" O2 Harness 24" O2 Harness
(rollover image for connector view)	O2 Extension Harness (black square 4-pin) These O2 extension harness are for the cars that need to move their O2 sensors back when running long tube headers. The terminals are factory style crimped and soldered and loom installed to help protect the wires. This harness uses the black square 4-pin style connectors. Available in different lengths. O2 Extension Harness: $15.00ea Select length: 6" O2 Harness 12" O2 Harness 18" O2 Harness 24" O2 Harness
(rollover image for connector view)	O2 Extension Harness (grey square 4-pin) These O2 extension harness are for the cars that need to move their O2 sensors back when running long tube headers. The terminals are factory style crimped and soldered and loom installed to help protect the wires. This harness uses the grey square 4-pin style connectors. Available in different lengths. O2 Extension Harness: $15.00ea Select length: 6" O2 Harness 12" O2 Harness 18" O2 Harness 24" O2 Harness
(rollover image for connector view)	O2 Extension Harness (black triangle 4-pin) These O2 extension harness are for the cars that need to move their O2 sensors back when running long tube headers. The terminals are factory style crimped and soldered and loom installed to help protect the wires. This harness uses the black triangle 4-pin style connectors. Available in different lengths. O2 Extension Harness: $15.00ea Select length: 6" O2 Harness 12" O2 Harness 18" O2 Harness 24" O2 Harness